JIEMA plate heat exchanger is a kind of heat exchanger made of thin metal plates that are pressed to corrugated shape, then stacked and fixed with bolts in a frame. Narrow and tortuous channels are formed between two plates. Then, heat exchange can be took place when the hot and cold work fluid flows through the channels.
Guide bar: Galvanized carbon steel, stainless steel
Introduction to Sheet
1.The unique-structure shunting area can balance fluid distribution.
2.The sheet is of unique linear and planar positioning structure, which can reduce the possibility for inter-sheet malposition.
3. Fillets in the sheet are of “Interlocked” structure which allows for mutual interlocking of sheets.
4.Design of large-angle ripples can raise heat transfer coefficient with fairly great reduction of resistance.
5.Design of small-angle ripples allows for reduction of degradation resistance and is featured by fairly low heat transfer coefficient.
6.Appropriate sheet type should be reasonably selected according to the parameters of working conditions at the time of design selection so as to achieve the best application effect.
7.Upper guide bar is designed with double slopes, which can improve stability of the sheets.
8.The inside part of clamping board is of bushing ring structure, which can improve matching accuracy.
9.The herringbone corrugated sheet is featured by high heat transfer efficiency; in addition, net-shaped contacts are formed in mutually reserve directions after the entire machine is assembled, featuring good pressure resistance.
Introduction to Sealing Gasket
Sealing gasket is inserted and fixed to the slot in heat-exchanging sheet, featuring easy insertion and replacement of sealing gasket, which can substantially reduce stoppage time. Sealing function is separated from fixing function. Even if some “clamps” with fixing function fail, the gasket can still have sealing function in the slot.
Applicable Temperature (ºC)
Anti-corrosive Performance and Applicable Occasions
Hot air, water, non-polar oil, mineral oil, lubricant and silicone oil, etc.
Vapor, polar chemical medium, alcohol, weak acid, weak alkali and oxidizing agent, etc.
Ammonia, mineral oil and lubricant, etc.
Inorganic acid, alkali, mineral oil and Haloalkane, etc.
Resistant to cold current and dry hot
Great logarithmic average temperature difference:
Plate heat exchanger can realize full countercurrent form; the temperature correction coefficient is 1.
High heat transfer coefficient
The corrugation of the sheet in plate heat exchange can make fluid generate turbulent flow with minor Reynolds number; its heat transfer coefficient is 3-5 times as large as that of shell-and-tube heat exchanger, reaching 7,000W/m2K at the most.
Small floor area
Plate heat exchanger features compact structure. The heat-exchanging area per unit volume is 2-5 times as large as that of shell-and-tube heat exchanger; the floor area occupied by plate heat exchanger is approximately one fifth to one tenth of the area occupied by shell-and-tube heat exchanger, given that the same heat exchange task is fulfilled by them.
Light weight and low price
The sheet in plate heat exchanger is only 0.5~0.8mm in thickness. The heat-exchanging area needed by it is smaller than that needed by shell-and-tube heat exchanger, given that the same heat-exchange task is fulfilled by them. The weight of plate heat exchanger is only around one fifth of the weight of shell -and-tube heat exchanger.
Small temperature difference at the end
As for water-water heat exchange, the lowest temperature difference at the end can be lower than 1℃, which is extremely beneficial to the recovery of low-temperature heat energy.
Low dirt coefficient
The dirt coefficient of plate heat exchange is small for the following reasons: Violent turbulent flow of fluid causes low-possibility deposition of impurities; the dead zone of inter-sheet channel is small; the heat-exchanging surface made of stainless steel is smooth, which results in less corrosive attaching.
Heat exchange with multiple media
Plate heat exchange allows for heat exchange with three or more media via the middle clapboard, which is extensively applied in milk product
To clean the sheet mechanically, unscrew the clamping bolt in plate heat exchanger to loosen the binding of plate and then unload the sheet, featuring extremely convenient maintenance.
Founded in 2005, JIEMA is one of the leading stainless steel removable plate heat exchanger manufacturers and suppliers in China for its excellent services and quality products. Welcome to buy the customized heat exchanger at cheap price from our factory. We can also offer you the quotation consultation if you need.